Features
Active power factor compensation with power
factor more than 0.98
Normal operating range , AC input voltage:
90~290V
Adoption of full bridge soft switch with efficiency
more than 91%
Damage free hot swap
Multi communication port
Excellent lightning proof design applicable to
thunder stormy areas.
Failure protection and alarm
Perfect battery management
Low radiation; Developed EMC design
The rectifier complies to requirements of CS and
RS EMC and relevant measuring method of power
equipment for communication
Of high reliability EN60950 and GB4943 compliance
Application
GSM/CDMA Base station
Mobile exchange bureau of
medium - small capacity
Satellite communication
Data exchange
Railway
Electric power system
Electric power system
Compliant to UL1 60950, CSA2C22.2 60950-00,
VDE30805 IEC60950
CE4 mark meets 73/23/EEC and
93/68/EEC directives.
Basing on years development and operating experience, GP48340A HF power system is a newly-designed product of Gold Power, which is of high performance and high reliability. The system adopts full bridge soft switch technology which greatly enhances the efficiency. It is also of wide rage of input voltage and operating temperature, high efficiency and the hot swap make it is easy for maintenance.
1 UL is the registered brand of Underwriters Laboratories
2 CSA is the registered brand of Canadian Standards Association
3 VDE is the registered brand of Verband Deutscher Elektrotechniker
4 All the products are CE compliance
GP48340A HF SWITCHING POWER SYSTEM
Cautions on electricity
1. High voltage
| Danger! |
Part of the component will be with high voltage during system operation. It will be fatal in the case of contacting the component with hand bare or with damp material |
The installation of AC power devices shall be strictly in accordance with field provisions.
Only staff with qualification of high voltage, AC power operation can undertake relevant
operation. The operator can't wear conductible object such as watch, ring and bracelet on
wrist. Immediately power off once water or dampness is found in cabinet.
If the operation is under damp environment, cabinet shall be rigidly prevented from the
moisture. Ban of switch on shall be hanged out if switch and button are not permitted to
switch on during installation.
| Danger! |
The operation of high voltage may cause fire disaster or electric shock. The wiring of AC cables shall strictly comply with local provisions. Only staff with qualification of high voltage, AC power operation can undertake relevant operations. |
2. Tools
| Danger! |
Special tools rather than common tools or self-bring tools shall be chosen for operation under high voltage or AC power. |
3. Storm
| Danger! |
Operations of high voltage, AC power, iron tower and mast are prohibited under lightning storm. |
The will be strong EM field in atmosphere under lightning storm. So duly GND shall
be implemented in case of device damaged by lightening.
4. ESD
| Caution |
The static generated by physic will damage the ESDS on circuit board (IC of large scale). So ESD wrist shall be taken along during device, flashboard, circuit board, IC chip contact. And make proper GND at one end of ESD wrist. |
5. Short circuit
| Danger! |
Short circuit of positive and negative of DC distribution or that caused by GND of non-GND pole is forbidden. As the power system is DC of constant voltage, the short circuit will get the device burned and cause disaster. |
Polarity of cable and terminals shall be strictly checked before operation with DC power.
Operation space of DC distribution is compact, and it should be planed before operation
undertaken. The operator can't wear conductible object such as watch, bracelet and ring
on wrist and tools for insulation shall be adopted. During the operation, the hand,
wrist and arm shall be in a state of activation to make minimum free distance if tools are loosened.
GP48340A HF SWITCHING POWER SYSTEM
6. Battery
| Danger! |
Safety notes of battery handling and connection method shall be acknowledged before battery operations. |
The nonstandard operation to battery will cause danger. So operator should be cautious
of short circuit or electrolyte overflow which may be a potential threat to device by
corrupting metal object and circuit board thus damage the device and cause circuit board
short circuit. Following notes are for operation safety:
Take off conductible objects such as the watch, bracelet and ring.
Use specific insulation tool and eye-protecting fixture and make preventive measures.
Wear the rubber groove and apron in the case of electrolyte overflow.
The battery electrode shall face up during handling. Inversion and slope are forbidden.
Others
1Point
| Danger! |
Protective groove is necessary during handling in case of cut by the edge. |
2 Power cable
| Danger! |
Confirm if the cables and marks are identical to actual installation before the cables are connected. |
3 Fastening of signal cable
| Danger! |
The signal wire shall be wrapped separately from wires of strong current or high voltage at distance of at least 150mm. |
Safety notes:
Please read the instructions and notes before operation to avoid accidents. The tag of
"Caution, warning, danger" in product and manual doesn't mean all the safety notes,
but a complementation. So the installer shall be professionally trained to take any operation.
All operations shall be in accordance with field provisions and special directives.
Audited Supplier 
){kind=link}
){kind=link}